8 images led motorcycle wheel lighting

Date: 15.10.2018, 00:44 / Views: 83394
Закрыть ... [X]

wheel Strobe rate is adjustable from 1 flash per second up to 3 flashes per second on each side.

Strobe sequence Wig WAG alternates (2 flashes left followed by 2 flashes right) between the right tube & left tube

Turns any led bulbs or lights into an instant emergency flasher/ warning system

Note: Our packages are not automatically insured against loss during shipping. Insurance is the responsibility of the purchaser!
.00 for each 0 unit of insurance

General Notes:

One module can connect to more than one led bulb, but each bulb must be connected to a module in order for that light to flash. In most instances (to avoid running extra wiring), it is easiest to install one module at each led light (ie: one module on each side of the vehicle). If you have more than one brake light on each side of the vehicle, one module can be used on each side (2 modules for four lights).

Important: The FM-00 dual circuit module has the words "FLASHING CONTROL MODULE" molded into the black case. The end closest to the word "FLASHING" must be toward the battery, and the word "MODULE" must be oriented closest to the led bulb. If the module is installed backwards, it will not work.

Operating Voltage: 6 - 13.5 volts

Maximum Current : 800ma

Note: These modules are not suited for filament style bulbs. A filament style bulb is not capable of fast switching, and cannot strobe. The power draw of the filament style bulb will destroy the Flashing Modules.

FLASHING LED CONTROL MODULES

The FM-00, FM-01 and FM-02 BRAKER CONTROL MODULES CAN MAKE YOUR led brake lights or reverse lights strobe brightly for a few seconds every time you hit the brakes or switch into reverse.

.........After a few seconds the lights stays bright as long as your foot is on the brake or the vehicle is in reverse.

The FM-01 and FM-02 BRAKER CONTROL MODULES CAN MAKE any led lights strobe continuously.

The FM-03 BRAKER CONTROL MODULES CAN MAKE YOUR led brake lights or reverse lights strobe brightly for a few seconds every time you hit the brakes or switch into reverse.

.........After a few seconds the lights stays bright as long as your foot is on the brake or the vehicle is in reverse. The module will then strobe again for 2 seconds when the pedal is first released or when you switch out of reverse.

WORKS WITH ANY LED LIGHTS

WORKS GREAT FOR LED BRAKE LIGHT OR REVERSE LIGHT BULB

Works great for upper 3d brake lights too!

Note: May not work with some vehicles that modulate voltage to a single circuit bulb for brake indication. Also may not work in some vehicles if the circuit does not completely shut off power when the brake is released.

Led Strobe Module Led Strobe Module Brake Lights Reverse Lights Continuous
10 Hz (10 flashes/sec) Continuous
20 Hz (20 flashes/sec) Click on images above for larger view Dual Function:

White Wire: Strobes for 2 seconds When you First Brake or Switch into Reverse.
Blue Wire: Strobes Constantly

Single Function:

Strobes When you First Brake and Again When you Release the Brake

Dual Function:

White Wire: Strobes for 2 seconds When you First Brake or Switch into Reverse.
Blue Wire: Strobes Constantly

Single Function:

Red Wire: Strobes for 2 seconds When you First Brake or first shift into reverse.

Single Function:

Blue Wire: Strobes for 2 seconds When you First Brake or first shift into reverse.

Led Strobe Module Led Strobe Module Led Strobe Module Flashing LED Brake Light Module FM-02A (10 Hz) FM-02B (20 Hz) FM-03A (10 Hz) FM-03B (20 Hz) FM-01A (10 Hz) FM-01B (20 Hz) FM-00 (20 Hz) Miniature Module FM-04 (20 Hz) With Continuous or Intermittent Strobe Modes With Intermittent Strobe Mode on Brake and Release With Continuous or Intermittent Strobe Modes With Intermittent Strobe Mode on Brake With Intermittent Strobe Mode on Brake or Reverse

Universal Compact Two Function Strobe Module

Improved Design

Only 1-3/4" x 1-3/8" x 1"

New design has no battery to burn out

Universal Compact Strobe Module

Improved Design

Only 1-3/4" x 1-3/8" x 1"

New design has no battery to burn out

Universal Two Function Strobe Module

3-3/8"x 2"x 7/8"

New design has no battery to burn out

Dual Compact Circuit Braker Module

2"x 1"x 3/8"

New design has no battery to burn out

 

Dual Compact Circuit Braker Module

2-3/4"x 1-1/2"x 1"

.99 EA

.99 EA

.99 EA

$ 5.99 EA

.99 EA

Uses:

7507, 1156,3156, 7440, 921 single circuit bulbs & 7225, 1157, 3157, 7443 dual circuit bulbs, or use with any led light bulb or led fixture. Can be used in any 6 or 12 volt (-) ground or (+) ground systems.

Common Applications:

Brake light Warning Strobe
Reverse Light Warning Strobe

Make any led bulbs or lights strobe continuously.STYLE="font-size: xx-small">

Function:

The FM-02 module contains a chip that will cause an led light bulbs to operate as follows (Note: Use either the White wire or Blue wire not both):

Function 1 (If you use the White Wire)

1. Each time power is applied to the red wire, from the battery, the white wire to the led bulb will cause the led bulb to perform a sequence as follows;

A. The led will strobe brightly for a few seconds and then stop strobing.

B. After a few seconds of strobing, the led light will light bright in a constant-on mode for as long as power is continually applied to the circuit (ie: as long as the brake pedal is pressed).

C. When power is cut to the brown wire (ie: the brake pedal is released, the bulb will go dim.

Note 1: In a singe circuit bulb such as an 1156 or 921, there is no dim circuit, so the module will sequence whenever the brake is applied, but there will be no dim function.

Function 2 (If you use the Blue Wire)

1. Each time power is applied to the red wire, from the battery, the blue wire to the led bulb will cause the led bulb to strobe continuously until power to the red wire is off.

Note 1: In a singe circuit bulb such as an 1156 or 921, there is no dim circuit, so the module will sequence whenever the brake is applied, but there will be no dim function.

Note 2: This module can also be used in a positive ground 6 or 12 volt electrical system.

Uses:

7507, 1156,3156, 7440, 921 single circuit bulbs & 7225, 1157, 3157, 7443 dual circuit bulbs, or use with any led light bulb or led fixture. Can be used in any 6 or 12 volt (-) ground or (+) ground systems

Common Applications:

Brake light Warning Strobe
Reverse Light Warning Strobe

The FM-03 module contains a chip that will cause an led light bulbs to operate as follows:

1. Each time power is applied to the white wire, from the brake circuit, the led bulb will perform a sequence as follows;

A. The led will strobe brightly for a few seconds and then stop strobing.

B. As long as power is still applied from the white-blue brake wire, the led light will light bright for as long as power is continually applied to the circuit (ie: as long as the brake pedal is pressed).

B. When power is cut to the white wire (ie: the brake pedal is released, the bulb will flash again for 2 seconds and then go dim.

Note: In a singe circuit bulb such as an 1156 or 921, there is no dim circuit, so the module will sequence whenever the brake is applied, but there will be no dim function.

Note 2: This module can also be used in a positive ground 6 or 12 volt electrical system.

Uses:

7507, 1156,3156, 7440, 921 single circuit bulbs & 7225, 1157, 3157, 7443 dual circuit bulbs, or use with any led light bulb or led fixture. Can be used in any 6 or 12 volt (-) ground or (+) ground systems,

Common Applications:

Brake light Warning Strobe
Reverse Light Warning Strobe

Make any Led bulbs or lights strobe continuously.

Function:

The FM-01 module contains a chip that will cause an led light bulbs to operate as follows (Note: Use either the White wire or Blue wire not both):

Function 1 (If you use the White Wire)

1. Each time power is applied to the red wire, from the battery, the white wire to the led bulb will cause the led bulb to perform a sequence as follows;

A. The led will strobe brightly for a few seconds and then stop strobing.

B. After a few seconds of strobing, the led light will light bright in a constant-on mode for as long as power is continually applied to the circuit (ie: as long as the brake pedal is pressed).

C. When power is cut to the brown wire (ie: the brake pedal is released, the bulb will either go dim.

Note 1: In a singe circuit bulb such as an 1156 or 921, there is no dim circuit, so the module will sequence whenever the brake is applied, but there will be no dim function.

Function 2 (If you use the Blue Wire)

1. Each time power is applied to the red wire, from the battery, the blue wire to the led bulb will cause the led bulb to strobe continuously until power to the red wire is off.

Note 1: In a singe circuit bulb such as an 1156 or 921, there is no dim circuit, so the module will sequence whenever the brake is applied, but there will be no dim function.

Note 2: This module can also be used in a positive ground 6 or 12 volt electrical system.

Uses:

7507, 1156,3156, 7440, 921 single circuit bulbs & 7225, 1157, 3157, 7443 dual circuit bulbs, or use with any led light bulb or led fixture. Can be used in any 12 volt (-) ground or (+) ground systems. Will not work in 6 volt systems.

Common Applications:

Brake light Warning Strobe
Reverse Light Warning Strobe

Function:

The FM-00 module contains a chip that will cause an led light bulb or any 12 volt led light to operate as follows:

1. Each time power is applied to the brown wire, from the battery, the black wire to the led bulb will cause the led bulb to perform a sequence as follows;

A. The led will strobe brightly for a few seconds and then stop strobing.

B. After a few seconds of strobing, the led light will light bright in a constant-on mode for as long as power is continually applied to the circuit (ie: as long as the brake pedal is pressed).

C. When power is cut to the brown wire (ie: the brake pedal is released, the bulb will go dim.

Note 1: In a singe circuit bulb such as an 1156 or 921, there is no dim circuit, so the module will sequence whenever the brake is applied, but there will be no dim function.

Note 2: This module can also be used in a positive ground 12 volt electrical system.

Note 3: The FM-00 has a built in circuit that will temporarily suspend the strobing effect if the brake pedal is pressed repeatedly. The strobe chip sill only reset if the brake is released for about 5 seconds or more.

Uses:

7507, 1156,3156, 7440, 921 single circuit bulbs & 7225, 1157, 3157, 7443 dual circuit bulbs, or use with any led light bulb or led fixture. Can be used in any 6 or 12 volt (-) ground or (+) ground systems

Common Applications:

Brake light Warning Strobe
Reverse Light Warning Strobe

Function:

The FM-01 module contains a chip that will cause an led light bulb or any 6 or 12 volt led light to operate as follows:

1. Each time power is applied to the brown wire, from the battery, the black wire to the led bulb will cause the led bulb to perform a sequence as follows;

A. The led will strobe brightly for a few seconds and then stop strobing.

B. After a few seconds of strobing, the led light will light bright in a constant-on mode for as long as power is continually applied to the circuit (ie: as long as the brake pedal is pressed).

C. When power is cut to the brown wire (ie: the brake pedal is released, the bulb will either go dim.

Note 1: In a singe circuit bulb such as an 1156 or 921, there is no dim circuit, so the module will sequence whenever the brake is applied, but there will be no dim function.

Note 2: This module can also be used in a positive ground 12 volt electrical system. If you have a (+) positive ground volt system, The module must be installed inline in the (+) Ground wire and the blue wire must be installed toward the led light or bulb. The brown wire must be installed toward the bulb.

Installation:

Install the module anywhere between the battery power and the led light that you wish to make flash. Connect the wires as follows:

Connect the flashing module in the wires feeding to any led bulb as follows:

White Wire - Connect to the (+) side of any led light(s) that you want to strobe intermittently for the first 20 ms).

Red Wire - Connect to (+) Wire on the Power or Battery Side.

Black Wires - Splices into to the - ground wires on both sides.

Blue Wire - Connect to the (+) side of any led light(s) that you want to strobe continuously.

Note 1 : You do not have to use both the white wires and the blue wires at the same time. You can and normally would use one or the other.

WARNING Never allow any of the bare wires connected to the module to touch together if power is connected to the module. This can instantly and permanently damage the module.

Installation:

Install the module anywhere between the battery power and the led light that you wish to make flash. Connect the wires as follows:

Connect the flashing module in the wires feeding to any led bulb as follows:

Blue Input Wire - Connect to the (+) battery power to power the module.

White Input Wire - Connect to (+) Brake Circuit.

Black Input Wire - Connect to the - ground wire.

Red Output Wire - Connect to the (+) side of any led light(s) or Bulb(s).

Black Output Wire - Connect to to the - ground wire going to the led light.

Note: You must connect the blue wire to a 12+ constant-on circuit. This circuit must have + power on after the brake pedal is released of the light will not flash when the brake pedal is released.

WARNING Never allow any of the bare wires connected to the module to touch together if power is connected to the module. This can instantly and permanently damage the module.

Installation:

Install the module anywhere between the battery power and the led light that you wish to make flash. Connect the wires as follows:

Connect the flashing module in the wires feeding to any led bulb as follows:

White Wire - Connect to the (+) side of any led light(s) that you want to strobe intermittently for the first 20 ms).

Red Wire - Connect to (+) Wire on the Power or Battery Side.

Black Wires - Splices into to the - ground wires on both sides.

Blue Wire - Connect to the (+) side of any led light(s) that you want to strobe continuously.

Note: You do not have to use both the white wires and the blue wires at the same time. You can and normally would use one or the other.

WARNING Never allow any of the bare wires connected to the module to touch together if power is connected to the module. This can instantly and permanently damage the module.

Installation:

The FM-00 module can be used in conventional (-) ground systems and (+) ground 12 volt systems. It will not work in 6 volt systems.

Install the module anywhere between the battery power and the led light that you wish to make flash. Connect the wires as follows:

Connect the flashing module in the wires feeding to any led bulb as follows:

Important: The dual circuit module has the words "FLASHING CONTROL MODULE" molded into the black case. The end closest to the word "FLASHING" must be toward the battery, and the word "MODULE" must be oriented closest to the led bulb. If the module is installed backwards, it will not work.

Power must flow thru the module and then to the led lights or bulbs that you want to make flash.

Red Wires - Connects to the (+) brake light wire.

Black Wires - Connects to the (-) ground wire.

WARNING Never allow any of the bare wires connected to the module to touch together if power is connected to the module. This can instantly and permanently damage the module.

Installation {Conventional (-) ground system} :

Install the module anywhere between the battery power and the led light that you wish to make flash. Connect the wires as follows:

Connect the brown wire to the wire coming from the (+) battery side of the circuit.

Connect the blue wire to the (+) wire going to the led light or light bulb.

Installation {Positive (+) ground system} :

Install the module anywhere between the battery power and the led light that you wish to make flash. Connect the wires as follows:

Connect the blue wire to the wire coming from the (+) battery side of the circuit.

Connect the brown wire to the (+) wire going to the led light or light bulb.

WARNING Never allow any of the bare wires connected to the module to touch together if power is connected to the module. This can instantly and permanently damage the module.


Wireless Remote Control

on/off Switch

12 Volt DC Input

60 watt maximum output.

5 amp capacity.

26mm x 54mm x 26mm Deep

1" x 2" x1" Deep

12 Volt input.

12 Volt output.

Wires wireless transmitter

Capacity:
  • (50) 3led utility lights
  • (50) 8led utility lights
  • (30) 24led utility lights
  • (30) 13led utility lights
  • (30) LED Strobes
  • (30) Bright Strobes
  • (30) MR16 18led bulbs
  • (140) 9led festoon bulbs

.99 Each

Choose Color

Black/Blue

Choose Type

12 Volt

LED Flasher Module

2 VDC Input

6 watt maximum output.

500 milliamp capacity.

Slow - 20-30 cylces per minute

Fast - 90-200 cycles per minute

75mm x 65mm x 30mm Deep

3" x 2-1/2" x1-1/8" Deep

12 Volt input.

12 Volt output.

2 screw mount

Capacity:
  • (5) 3led utility lights
  • (5) 8led utility lights
  • (3) 24led utility lights
  • (3) 13led utility lights
  • (3) LED Strobes
  • (3) Bright Strobes
  • (3) MR16 18led bulbs
  • (14) 9led festoon bulbs

.99 Each

Choose Color

Black

Choose Type

Fast Slow

Manual ON/OFF LED Switch Module (With Flash)

2 VDC Input

6 watt maximum output.

500 milliamp capacity.

Flashes at 90-200 cycles per minute

75mm x 65mm x 30mm Deep

3" x 2-1/2" x1-1/8" Deep

12 Volt input.

12 Volt output.

2 screw mount

Capacity:
  • (5) 3led utility lights
  • (5) 8led utility lights
  • (3) 24led utility lights
  • (3) 13led utility lights
  • (3) LED Strobes
  • (3) Bright Strobes
  • (3) MR16 18led bulbs
  • (14) 9led festoon bulbs

.99 Each

Choose Type

With Flash

Choose Type

On/Off

Manual ON/OFF LED Switch Module (No Flash)

2 VDC Input

6 watt maximum output.

500 milliamp capacity.

75mm x 65mm x 30mm Deep

3" x 2-1/2" x1-1/8" Deep

12 Volt input.

12 Volt output.

2 screw mount

Capacity:
  • (5) 3led utility lights
  • (5) 8led utility lights
  • (3) 24led utility lights
  • (3) 13led utility lights
  • (3) LED Strobes
  • (3) Bright Strobes
  • (3) MR16 18led bulbs
  • (14) 9led festoon bulbs

.99 Each

Choose Type

No Flash

Choose Type

On/Off

Strobe Light Manual Steel on/off Toggle Switch With wires & fuse

Thru Hole Screw Mount

.99 Each

Choose Color

2 Way

Choose Type

With Wires



Похожие новости


Cupcakes ideas decorations 2018
Long black dress tumblr 2018
Psychedelic trippy flowers 2018
Light blue colored jeans outfit 2018
Ashlee simpson hair 2018




ШОКИРУЮЩИЕ НОВОСТИ